Short answer: how is TC fabric dyed to one shade?
TC (T/C) fabric is a blend of polyester and cotton, and it cannot be dyed with a single dye class: the polyester side takes disperse dyes (dyed at high heat, around 130–140°C in a jet, or by the continuous thermosol route) and the cotton side takes reactive dyes (60–80°C, fixed with alkali). The single shade you see is the balance of those two dye classes, controlled in a colour lab — that is the core difficulty of TC dyeing.
What TC (T/C) fabric is — and why it needs two dye systems
TC (T/C) is a blend of polyester (T) and cotton (C). Manufacturers like it because it takes the best of both fibres: polyester gives shape retention, low shrinkage and easy ironing, while cotton gives absorbency, skin comfort and breathability — which is why TC, alongside TR, is a main uniform fabric (office, hotel, factory workwear).
The difficulty is that "one fabric carries two fibres":
- Polyester is hydrophobic — it only takes disperse dyes: small molecules that enter the fibre at high temperature (HTHP jet, or continuous thermosol at 180–220°C)
- Cotton is cellulosic — it takes reactive dyes, which form a chemical bond with cellulose at 60–80°C, fixed with alkali
- One TC fabric therefore has to pass through two dyeing systems before it comes out as one shade
The two-bath TC dyeing process, step by step
The most widely used method is dyeing the two fibres in sequence (two-bath):
- Pretreatment: desizing, scouring (and bleaching where needed), plus heat setting for the polyester — essential; if the polyester is not heat-set first, the fibre relaxes and the fabric loses its shape after dyeing
- Polyester dyeing: disperse dyes at mildly acidic pH (about 5–6) with a dispersing agent and a levelling agent, in a high-temperature jet (HTHP, up to about 140°C)
- Reduction clearing: strips disperse-dye staining from the cotton side before the cotton dye step — used whenever the shade leaves cotton-side staining
- Cotton dyeing: reactive dyes (jet or pad-batch — the cotton side of TC is often run as pad-batch, a semi-continuous route that fixes at room temperature without steaming, saving energy)
- Soaping and washing: unreacted dye is washed out at heat with detergent, then rinse and dry
- Finishing: for example shrinkproofing (sanforizing) to lock in the final shape
Alternatives: one-bath (both dye classes in a single bath — only works when the dyes do not stain each other) and continuous thermosol (padding with disperse dye, dry heat at 180–220°C, cotton dyed in a separate step) — suited to long runs of a single shade.
The two dye classes side by side: disperse vs reactive
The two dye classes used in TC are completely different — which is why they cannot be swapped:
- Fibre they take: disperse = polyester (synthetic fibre) / reactive = cotton (cellulose)
- Bonding mechanism: disperse = small molecules physically diffuse into the fibre at high temperature / reactive = form a covalent bond with cellulose
- Dyeing temperature: disperse = 130–140°C (HTHP jet) or 180–220°C (thermosol) / reactive = 60–80°C
- pH: disperse = mildly acidic (about 5–6) / reactive = alkaline (fixed with alkali)
- Fastness: disperse gives good lightfastness on the polyester side / reactive gives good wash fastness after soaping — a blend's overall fastness is always limited by the weaker side
One shade: how a dyeing mill keeps it consistent
A TC shade is the sum of two dyes — keeping it consistent takes:
- A colour lab: spectrophotometer plus a multi-source light booth for lab dips
- Lab dyeing that mirrors the production route (batch and continuous) — a sample that cannot be repeated on the production line is not a match
- A buyer-signed standard sample held for inter-order comparison
- A locked recipe and process conditions (dye level per class, auxiliaries, temperature, time, pH)
- ΔE from the spectrophotometer: measures the colour difference of every lot against the standard — the tolerance level must be agreed between buyer and mill from the start
This is why colour control needs a colour lab and a measured standard.
TC vs 100% cotton vs TR
- 100% cotton: a single dye class (reactive/vat/direct); the best hand and absorbency, but the highest shrinkage
- TC: two dye classes; good shape retention, low shrinkage, easy care — a main uniform fabric alongside TR
- TR: heavier and softer than TC with a smoother hand, but slightly less durable (rayon is weaker when wet) — choose by the duty of the uniform
Colour fastness of TC fabric: tests and spec lines
The fastness of a blend is set by the weaker fibre side — usually the reactive-dyed cotton. The test methods used in practice (name the method and the level in the spec):
- Wash fastness: ISO 105-C06 (AATCC 61)
- Dry crocking: ISO 105-X12 (AATCC 8)
- Light fastness: ISO 105-B02 (AATCC 16), rated on the Blue Wool scale 1–8
- Perspiration: ISO 105-E04 (AATCC 15)
- Dimensional change: ISO 6330 (AATCC 135)
The buyer sets the levels to fit the duty (for uniform work, 4 or better is the usual floor) — once the method is named, results are comparable.
Spec lines you can copy
- "TC fabric, polyester/cotton blend"
- "Dyed with disperse (polyester) + reactive (cotton), two-bath process"
- "Wash fastness ≥ 4 (ISO 105-C06)"
- "Dry crocking ≥ 4 (ISO 105-X12)"
- "Light fastness ≥ 4 (ISO 105-B02, Blue Wool)"
- "Dimensional stability per AATCC 135"
Boonchuay Industrial (BCI): a dyeing mill that has run TC for over 60 years
BCI (Boonchuay Industrial) is a fabric dyeing and finishing mill with over 60 years of experience, in Nakhon Pathom, Thailand. It takes TC and TR — its core uniform fibres — as commission dyeing (fabric dyeing). What it brings:
- The full route: pretreatment (desizing/scouring), dyeing, finishing, and a colour lab
- Both batch (jet) and continuous equipment; BCI's continuous route covers light to dark shades, which suits long-run uniform fabric
- Three QC checkpoints: greige inspection before dyeing, in-process control and inspection at packing — with a 10-point system quality report for every lot
- Testing to ISO, JIS, AATCC and Daimaru methods
- OEKO-TEX Standard 100 certification — no restricted substances in the finished fabric
- MOQ is negotiable — it depends on process, shade and order size
Q&A
Q: Why can't TC be dyed with one class of dye? A: Disperse dyes bond to polyester only and not to cotton; reactive dyes bond to cellulose only and not to polyester. A single class leaves the other fibre undyed.
Q: TC, TR or 100% cotton for work uniforms? A: TC and TR are both main uniform fabrics: TC gives shape retention, low shrinkage and easy care; TR is heavier and softer but slightly less durable. 100% cotton is the most comfortable but shrinks most. BCI dyes all three — match the fibre to the duty and the budget.
Q: Why does the same shade drift between orders? A: A blend shade is the sum of two dye classes, so any drift in recipe or process moves the colour. Lock an approved standard and check every lot with a spectrophotometer. (Read: Why Do Two Lots of the Same Colour Look Different?)
Q: What should the spec say so results are comparable? A: Name the method and the level: wash (ISO 105-C06), crocking (ISO 105-X12), light (ISO 105-B02), shrinkage (AATCC 135). BCI tests in its in-house lab and issues a 10-point system quality report for every lot.
Q: Can small quantities be dyed? A: MOQ is negotiable — it depends on process, shade and size; small runs can go on the batch (jet) route.
Q: Does 65/35 TC dye differently from 80/20 TC? A: Yes. The higher the polyester share, the more the disperse-dye contribution shows in the overall shade, so the recipe (the balance of the two dye classes) must be set per ratio in the lab dip — always give the mill the true fibre ratio to control the shade accurately.
Talk to BCI
Commission TC fabric dyeing · Uniform fabrics · Contact the team
References
- Dyeing of Polyester and Cotton (P/C) Blend Fabric — Textile Learner
- Textile Dyeing (Dyeing Booklet) — CottonWorks, Cotton Incorporated
- ISO 105-C06:2010 Textiles — Tests for colour fastness — Part C06: Colour fastness to household and commercial laundering — ISO
- ISO 105-B02:2014 Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc — ISO
- Standard Test Methods and Procedures — AATCC

