Short answer: what is shade variation between dye lots?
Even when dyed to the same spec in every respect, a new dye lot can differ slightly from the last one — that is "normal" in dyeing any fabric, and it is not a defect in itself. What decides whether a lot passes is the shade band (the acceptable range) agreed in the spec.
A professional dyeing mill controls this with three things: the approved lab dip kept as the master standard, every lot measured with a spectrophotometer against that standard using a named method and a ΔE (delta E) value, and the dye recipe recorded so it can be repeated.
"Slightly different" and "out of shade band" are different things
- Shade variation is a small colour difference between two lots dyed to the same standard — it can always happen, and it is managed with a tolerance.
- Out of shade band is a difference that exceeds the tolerance agreed in the spec — only that is a defect.
Simple way to remember: slightly different = normal / beyond what was agreed = a defect. A good fabric specification therefore does not ask "is the colour 100% identical?" but "how is it measured, and how big a difference is unacceptable?"
Why the colour shifts between lots
The recipe is unchanged, yet the result still varies, because several variables move from lot to lot:
- Dye strength — dye from different manufacturers or production batches has different strength, even for the same dye, so the mill must check strength and adjust the recipe for each lot
- Raw material — natural fibres, such as cotton, absorb dye unevenly from yarn lot to yarn lot
- Water and dyeing conditions — water quality, temperature, time and pH in the dyebath all matter
- Scaling from lab to bulk — small trial dyeings in the lab and large production runs run under different conditions
These cannot be forbidden, but a well-run mill "measures and corrects" every lot.
How it is measured: instrument plus eye, together
- Visual check in a light booth — the new lot is compared with the master standard under standard illuminant D65 (daylight), plus a second light source, to catch differences the eye can miss (metamerism)
- Spectrophotometer — measures colour numerically and reports ΔE (delta E): the size of the colour difference; smaller is closer
- The ΔE formula — ISO 105-J03 (the CMC formula) gives a single number that lets the buyer set a tolerance independent of the colour; CIEDE2000 (ISO/CIE 11664-6) is the formula the CIE recommends for small differences used in pass/fail decisions
The buyer should write "measurement method + tolerance" into the spec — for example ΔE to ISO 105-J03 against the master standard, with the tolerance set by the use. Details of ΔE and lab dip colour matching are in Lab Dip: how fabric colour matching works.
How a dyeing mill keeps repeat orders matching
- The colour standard starts with the customer — a spec, a colour sample to match, or a standard colour from the mill's swatch card
- The approved lab dip becomes the master standard — the mill stores this piece protected from light, together with its recipe, as the target for every lot
- The recipe is recorded and dosed by an automatic colour dispenser — removes human dosing error
- Trial dyeing in the lab duplicates the mass-production process — the colour approved in the lab is the colour production will make
- Every lot is measured before release — spectrophotometer plus visual check in a multi-source light booth, against the master standard
- In-process QC and pre-packing inspection — greige inspection before dyeing, process control, inspection at packing, with a quality report
- The shade band in the spec — the maximum acceptable ΔE for re-orders; every new lot, even months later, is measured against the master standard within that band
Spec lines a buyer can copy
- Master standard: the approved lab dip, kept by both parties
- Measurement: ΔE to ISO 105-J03 (or CIEDE2000) against the master standard, under D65
- Shade band: the maximum acceptable ΔE for re-orders
- Re-orders: every lot is measured against the stored standard; out-of-band lots are reported before shipment
- Colour standard: a stored sample protected from light plus a measurement record (spectral data), because the physical sample changes over time
Boonchuay Industrial: over 60 years of dyeing and finishing
Boonchuay Industrial (BCI) is a commission dyeing and finishing mill in Nakhon Pathom, with over 60 years of experience. For colour, BCI runs a colour lab with a spectrophotometer, a multi-source light booth and an automatic lab colour dispenser; the lab dyes trial samples in both batch and continuous processes that duplicate the mass-production process, so the colour approved in the lab is the colour production makes. Quality control has three stages — greige inspection before dyeing, in-process control and inspection at packing — with a 10-point system quality report, and the in-house lab tests to ISO, JIS, AATCC and Daimaru. BCI runs batch (jet) and continuous dyeing to fit each volume and keeps colour consistent across many colours and lots; minimum order (MOQ) is negotiable.
See the fabric dyeing and finishing services page or the Our Standards page for more.
FAQ
Is a slight colour difference on a re-order normal? Yes — a small difference between lots can happen with every fabric. What matters is that the difference stays inside the shade band agreed in the spec; beyond that, there must be an agreed process (report, adjust, re-dye).
How do you know a lot passes or fails? Measure the lot's ΔE against the master standard (the approved lab dip) using the agreed formula (ISO 105-J03 or CIEDE2000) under D65, and also check it visually in a light booth — both must pass.
The recipe is the same — why is the colour not the same every time? Because dye strength differs between dye batches, the raw material and water quality vary, and the dyebath conditions (temperature, time) move from lot to lot. The mill therefore measures every lot and adjusts the recipe instead of simply re-using it.
How long does the colour standard last? The fabric sample must be stored away from light and heat, and a measurement record (spectral data) should be kept alongside it, because the sample changes over time. A good mill keeps both.
If a re-order lot is out of the shade band, what are the buyer's options? Agree in advance: accept with a note (when the small difference is acceptable), re-shade, or re-dye. Having this process in the spec from the start avoids disputes when the fabric arrives.
Talk to BCI
If you are looking for a dyeing mill that holds repeat orders to named standards, contact Boonchuay Industrial — commission dyeing and finishing, over 60 years, Nakhon Pathom — at Contact Us.
References
- ISO 105-J03:2009 Textiles — Tests for colour fastness — Part J03: Calculation of colour differences, ISO
- Lab Dip Process, CottonWorks (Cotton Incorporated)
- SP 15-4 Handbook of Textile Testing Part-4: Identification and Testing of Dyestuffs (1988), Bureau of Indian Standards
- Westland S, Pan Q (2017) Advances in Instrumental Colour Pass/Fail Analysis, Journal of Textile Science and Engineering 7:321
- AATCC Test Methods, AATCC

