Sanforizing is a mechanical finishing process used to reduce the residual shrinkage of woven fabric before cutting and sewing. It aims to limit later dimensional change, but the result depends on the fabric, process settings, and washing and drying conditions, so it should be checked against a stated specification. In an early patented method, fabric is moistened and held against a contractible support while pressure shortens it; the changed dimensions are then set, preferably with heat and pressure.
What sanforizing is
- A mechanical finishing process based on controlled compressive shrinkage: pressure shortens woven fabric in one or both directions before it is made into garments.
- An early US patent titled Art of shrinking fabrics, filed by Sanford L. Cluett in 1930, was granted in 1932; its description covers moistening, compressing and setting textile fabric.
- This guide focuses on sanforizing for woven fabrics. Suitability for a particular fabric depends on its composition, construction and performance specification.
Why fabric shrinks, and where sanforizing acts
- In woven cloth, interlacing creates crimp in warp and weft yarns; the early patent describes compression as a way to rearrange yarns and reduce the fabric’s dimensions.
- Dimensional change after laundering is fabric- and test-specific. ISO 6330 specifies different washing and drying procedures, while AATCC TM135 measures length and width changes after home laundering.
- There is no single shrinkage percentage for all cotton fabric. State the washing and drying conditions and acceptance limit, then test against that specification.
How the process works
- Moistening: the cloth is moistened so it can move during treatment.
- Controlled compression: pressure is applied while the cloth is held on a support that contracts in area, shortening it in the selected direction.
- Setting: the changed dimensions are set, preferably by drying under heat and pressure; equipment and settings vary by mill.
The finishing line at Boonchuay Industrial (BCI) includes sanforizing among its mechanical finishing steps.
Which fabrics use it
- The BCI profile lists office, hotel and industrial uniforms in TC or TR, and monk-robe fabrics in cotton or TC. Confirm whether the specified cloth needs sanforizing against its performance requirements.
- Give the mill the fibre content, construction and dimensional-change target so it can assess suitability against the fabric specification.
- The early patent describes woven fabric and changes in one or both dimensions. For knits or other constructions, do not assume the same process and result; ask the mill which route and test are appropriate.
Choose a finishing route by the measured result
- Sanforizing uses controlled mechanical compression to reduce later dimensional change in woven cloth.
- Other finishing routes use different processes and address different performance needs; environmental impact and shrinkage performance should be evaluated for the actual process and fabric.
- Compare the measured result with an agreed residual-shrinkage target under a named washing and drying method.
How to test and prove the result
- Use a named standard method and include it in the fabric specification.
- ISO 6330 defines domestic washing and drying procedures; use it together with ISO 5077 to determine dimensional change.
- AATCC TM135 is an alternative method to measure length and width changes after home laundering. Specify the washing and drying options to use.
- There is no universal post-laundering shrinkage limit for every sanforized fabric. State the acceptable change by direction, number of cycles, and washing and drying conditions.
- At BCI: dimensional stability is one of the test categories in the in-house lab — in-house lab tests to ISO, JIS, AATCC and Daimaru
- Quality control: three checkpoints: greige inspection before dyeing, in-process control and inspection at packing, plus a 10-point system quality report for every lot
How to specify it (buyer's checklist)
- State the target residual shrinkage (%) separately for warp and weft
- State the test method: ISO 6330 + ISO 5077, or AATCC 135, and the washing and drying conditions to simulate
- State the garment's care label (machine wash? tumble dry?) — the test should mirror what the garment will actually see
- Send the spec or a fabric sample to the BCI team so the finishing route can be confirmed for the cloth
- The minimum order quantity is negotiable with the team
FAQ
Will sanforized fabric never shrink?
No. Sanforizing aims to reduce residual dimensional change, not eliminate it. The measured result depends on the fabric and the washing and drying procedures, so agree a target and test it.
Do TC and TR uniform fabrics always need sanforizing?
It depends on the end customer's specification and end use. Ask the BCI team whether sanforizing or another finishing route should be evaluated, then test the fabric against the agreed limit.
Can knit fabric be sanforized?
The early patent describes a process for woven cloth. For knits or other constructions, do not assume the same process or result; ask the mill which dimensional-stability route and test are appropriate.
Where in the process does sanforizing sit?
It is a fabric-finishing step before cutting and sewing. The exact position in the line depends on the mill’s process sequence.
What shrinkage limit should a buyer specify?
There is no single suitable percentage for every fabric. State an acceptable change for length and width, name the washing and drying procedure, and test the fabric against that specification.
Talk to BCI
If a uniform or workwear brief includes a dimensional-change limit, the BCI team can discuss a suitable finishing route for the fabric and the test method to use. Contact us on the contact page, or see our fabric dyeing and finishing services.
Read more: Fabric shrinkage: causes and testing with ISO 6330 / AATCC 135
References
- Art of shrinking fabrics, US Patent 1,861,422 — Sanford L. Cluett (filed 1930; granted 1932)
- AATCC TM135-2025, Dimensional Changes of Fabrics after Home Laundering — AATCC
- ISO 6330:2021, Textiles — Domestic washing and drying procedures for textile testing — ISO
- ISO 5077:2007, Textiles — Determination of dimensional change in washing and drying — ISO

