Short answer: why does fabric shrink
Fabric shrinkage is the loss of size in length and width when cloth is exposed to water, heat or mechanical force — most of it happens in the first home launderings, because the fibres and yarns that were never fully relaxed during weaving, dyeing and finishing finally release the built-up tension and settle back to their natural state.
There are two reliable fixes: have the mill "pre-relax" the cloth before it ships (e.g. sanforizing, which makes the fabric do its shrinking at the mill) and specify a standard test with an acceptance value in the spec (e.g. dimensional change not exceeding 2% per ISO 5077), then verify against the actual production lot.
"Shrinkage" vs "growth"
Dimensional change can go either way, and standards report it as a percentage of the pre-wash size:
- Shrinkage — the fabric gets smaller after washing/drying; the most common case, especially with woven cotton-rich cloth
- Growth — the fabric gets larger; seen in some constructions where yarns were packed in above their equilibrium tension
Specs and test reports must state dimensional change for both warp and weft, separately — almost no fabric shrinks equally in both directions (wovens usually shrink more in length than in width).
What makes fabric shrink
Shrinkage comes from three levels of the fabric:
- Fibres — cellulosic fibres (cotton, rayon) absorb water and swell a lot, so they can move and re-set when wet. Synthetic fibres such as polyester swell little, so they change size less. This is why 100% cotton shrinks more than a blend, and the higher the cellulosic content, the higher the shrinkage tendency
- Yarns — yarns carry twist and were stretched taut at the loom. When wetted and laundered, the yarns relax toward their natural (shorter) length — the higher the weaving tension, the more potential shrinkage is stored
- Fabric structure — crimped yarns curl further when wet, and cloth that was pulled taut through dyeing and finishing without proper tension control keeps that stored tension waiting for the first wash
One more factor: the sizing that coats yarns at weaving. When sizing is stripped out during desizing/scouring, the fabric structure changes — if tension and drying method are not controlled in that step, the fabric keeps excess tension in reserve.
In one line: shrinkage = released tension that was stored since weaving. A good dyehouse's job is to release that tension before delivery, leaving low, consistent, testable residual shrinkage.
What is sanforizing?
Sanforizing is a mechanical pre-shrinking finish: the fabric is moistened with water or steam, then pressed against a moving, stretched rubber belt — as the belt relaxes, it forces the cloth to contract lengthwise with it, and the fabric is then dried so the new, shorter dimensions are set. The fabric does most of its shrinking at the mill instead of in the customer's washing machine.
- Sanforized fabric — residual shrinkage of about 1% or less in both directions; "Sanforized" is a registered trademark of this process, not a generic word
- Preshrunk fabric — a broader, generic term covering several methods; ask which method was used and for the residual shrinkage value
- Untreated fabric — woven cotton cloth left without shrinkage control can shrink several percent per home laundering, depending on construction and wash conditions, and often continues to move over several washes
There is also a chemical route: crosslinking resins applied in wrinkle-reduction (easy-care) finishing reduce shrinkage and hold dimensions at the same time — useful when you need "no ironing" and "stable size" in one (BCI offers easy-care finishing among its finishing services).
Testing: name the standard in the spec
A shrinkage test has two steps: "wash/dry by a defined standard method", then "measure size before and after". The standards buyers should know:
- ISO 6330 — defines the "domestic washing and drying procedures for textile testing" (reference washing machine, temperature, cycles, and several drying methods such as line drying, flat drying, ironing and tumble drying) — it is the "how you wash it" half of the test
- ISO 5077 — the method for measuring "dimensional change in washing and drying", referring to ISO 6330 for the washing and drying procedures
- AATCC 135 — AATCC's method for "dimensional changes of fabrics after home laundering", covering several wash temperatures × 3 agitation cycles × 4 drying methods — a good fit for garments laundered at home
- ISO 3759 — how test specimens are prepared, marked and measured for dimensional-change tests (used together with ISO 5077)
Working rule: the spec must state "method + acceptance value" — e.g. "Dimensional change ≤ 2% (length and width) — wash/dry per ISO 6330 (warm, gentle), line dry, measured per ISO 5077". Stating the drying method matters: tumble-dried cloth always shrinks more than line-dried cloth, and the measured value changes with the condition chosen.
Spec lines you can copy
- Dimensional change (warp/weft): ≤ 2% — ISO 5077, wash/dry per ISO 6330 (warm wash, line dry)
- High-launder items: ≤ 3% after 3 cycles per AATCC 135 (warm, tumble dry)
- Spirality/skew after washing: limit agreed with the buyer — ISO 16322-2
- Report results separately for warp (length) and weft (width), with the number of wash cycles stated
Remember: the value you get depends on the wash/dry method you chose — agree the test method with the mill before production starts, not after the fabric arrives.
How BCI controls fabric size
Boonchuay Industrial (BCI) in Nakhon Pathom, has offered commission dyeing and finishing for over 60 years. "Pre-relaxing" the cloth is inside BCI's finishing scope alongside calendering and its other finishing services — BCI offers sanforizing for jobs that need stable dimensions.
On testing, BCI's in-house laboratory checks "dimensional stability", as part of three-stage quality control (incoming, in-process, packing) and a 10-point quality report issued for every lot, tested to ISO, JIS, AATCC and Daimaru standards. See the full service list on the BCI fabric dyeing services page or contact the BCI team to specify shrinkage for your job — for high-launder uniform work, read the uniform fabrics guide to choose the right construction, and see the Fabric Spec Sheet for the full composition-plus-test data layout.
FAQ
Q: Will a TC blend shrink as much as 100% cotton? A: Less — the polyester portion swells little and "holds" the structure, while the cellulosic portion does most of the shrinking. But don't guess: ask for the measured value with the named method (ISO 5077 / AATCC 135) from the pre-production lot.
Q: What's the difference between "sanforized" and "preshrunk"? A: Sanforized is a registered trademark of the mechanical (rubber-belt) pre-shrinking process, held to about 1% or less residual shrinkage; preshrunk is a generic term covering several methods. Ask the mill which method was used and for the test report.
Q: Should I test the fabric or the garment? A: Test the fabric before cutting (that's the spec line), because a finished garment also contains linings, buttons and other pieces that shrink differently. For critical jobs, repeat the test at garment level to confirm.
Q: Does line drying vs tumble drying change the result? A: Clearly. Heat and tumbling let the fibres fully relax, so the "drying method" in the spec is a requirement, not an option — match it to how the end user will actually launder the item.
Q: If I also want "no ironing", does shrinkage improve? A: Yes — easy-care finishing uses crosslinking resins that reduce shrinkage and hold size at the same time — but also specify that strength values (tension/tear) stay within limits, because too much resin reduces the fabric's durability.
Q: Does BCI sanforize and report dimensional stability? A: Yes — sanforizing is one of BCI's finishing services, and its in-house lab checks dimensional stability to ISO / AATCC (and JIS, Daimaru), reported with the 10-point quality report — minimum order quantities are negotiable: share your lot and end use, and the team will work with you.
References
- ISO 5077:2007 Textiles — Determination of dimensional change in washing and drying, ISO
- ISO 6330:2021 Textiles — Domestic washing and drying procedures for textile testing, ISO
- AATCC Test Method 135-2025, Dimensional Changes of Fabrics after Home Laundering, AATCC
- ISP-1009 A Guide to Improved Shrinkage Performance of Cotton Fabrics, Cotton Incorporated
- Finishes on Fabrics, Current Information Series No. 257, University of Idaho Extension

