Flame-retardant (FR) fabric is treated with an FR chemical finish, or woven from fibres that resist flame inherently, so that it ignites with difficulty and spreads flame slowly when exposed to fire. No commercial workwear fabric is fully fireproof — the required level of protection depends on the applicable clothing standard and the verified test results. An FR label alone does not establish protection against molten materials or every heat hazard.
FR finish vs FR fibre: two ways to the same result
- FR finish (chemical): fabric woven from standard fibres (cotton, TC, TR) is impregnated with a flame-retardant chemical, then dried and cured. Agree the chemistry with the mill for the fabric and end use, and verify the required performance by the named test.
- FR fibre (inherently flame-resistant): the fibre chemistry itself resists flame — aramids, modacrylics, flame-treated cellulosic fibres. Note that polyester can melt and drip in intense heat — which is why garment standards such as NFPA 2112 require that the fabric does not melt and drip.
- For buyers, neither the fibre name nor the finish name is a performance guarantee. Specify the required clothing standard, fabric tests and laundering conditions, and confirm performance after the agreed laundering with the mill.
How is flame retardancy tested?
Test methods and performance requirements for the flame-resistant performance of textile products for human use:
- ISO 15025:2016 (Protective clothing — Protection against flame — Method of test for limited flame spread): two ignition methods — surface ignition and bottom-edge ignition — on vertically oriented flexible materials (single or multi-layer) against a small, defined flame source; not appropriate for materials that show extensive melting or shrinkage
- ISO 14116:2015 (Protection against flame — Limited flame spread materials, material assemblies and clothing): sets the minimum limited-flame-spread requirement and classifies materials, material assemblies and garments from the ISO 15025 test result
- Finished-garment standards: EN 11612 (EN ISO 11612:2015, European adoption of ISO 11612) and NFPA 2112 define what the finished garment must pass — ISO/EN 11612 sets minimum performance requirements for clothing against heat and flame (limited flame spread plus radiant, convective or contact heat, and molten metal splashes); NFPA 2112 covers flame-resistant clothing against short-duration thermal exposures from fire — the fabric must not melt and drip
- ASTM E84: a surface-burning test for building materials, not a personal-protection test — do not confuse the two
- BCI's in-house lab tests to ISO, JIS, AATCC and Daimaru standards; confirm with the BCI team where your FR test (e.g. ISO 15025) will be run — see how BCI tests fabric
The spec line to state: test method (ISO 15025) + pass criteria + number of industrial launderings the fabric must survive before the test.
How long does an FR finish last?
The FR chemical is applied as a finish, so it can be lost through industrial laundering. An FR workwear spec therefore always includes a wash-durability requirement: the number of industrial washes the fabric must survive, and a re-test of the FR performance after that number of washes.
How to specify an FR workwear fabric
Example spec line (adjust to your actual use):
Fabric: TC 65/35, [weight], [colour] Finish: flame retardant Test: ISO 15025 — [pass criteria] after [N] industrial washes
(Values in brackets are placeholders — agree them with the mill for your actual use.) Note: if the end use falls under a product standard (for example EN 11612, NFPA 2112 or a local tender spec), state the standard and the required test in the spec.
FR workwear fabric in Thailand: TC and TR
BCI offers chemical finishing, including flame-retardant finishing, as one of its chemical finishing services. Uniform and workwear fabric — including industrial workwear — is produced on TC and TR, both main uniform fabrics BCI works with.
FAQ
Q: Is "flame-retardant" the same as fireproof? A: No — an FR fabric ignites with difficulty, spreads flame slowly or self-extinguishes when the ignition source is removed. No commercial workwear fabric is fully fireproof.
Q: Which test should I ask the mill to run? A: For the fabric itself: ISO 15025 (limited flame spread). For the finished garment: the end-use standard, such as EN/ISO 11612 (heat and flame) or NFPA 2112 (flash fire / short-duration thermal exposure). Name the method in the spec — the word "flame-resistant" alone is not a test.
Q: Can FR be combined with other functional finishes? A: Yes — workwear fabric often needs FR together with water repellency, soil release or easy care. The chemistry and the order of finishing affect the final performance, so compatibility and the required wash count should be confirmed with the mill.
Q: How many washes must the fabric survive? A: It depends on the end use and the cleaning contract — specify the number of washes the garment will see in service, and require the FR re-test after that number.
Q: Can BCI handle FR workwear fabric end to end? A: Yes — BCI offers dyeing (batch and continuous routes), functional finishing including flame retardant, and works on TC/TR workwear fabric. MOQ is negotiable — talk to the team with your spec and the test you need.
Talk to BCI
BCI handles fabric for uniform and workwear applications — from colour matching and dyeing to chemical finishing and quality control — at its plant in Nakhon Pathom.
- A full range of chemical finishes (including flame retardant)
- In-house lab testing to ISO, JIS, AATCC and Daimaru standards
- QC: three checkpoints: greige inspection before dyeing, in-process control and inspection at packing
- A 10-point system quality report for every lot
- MOQ is negotiable
See our commission dyeing and finishing, uniform fabrics and functional finishes, or talk to the BCI team via the contact page.
References
- ISO 15025:2016 — Protective clothing — Protection against flame — Method of test for limited flame spread, ISO
- ISO 14116:2015 — Protective clothing — Protection against flame — Limited flame spread materials, material assemblies and clothing, ISO
- ISO 11612:2015 — Protective clothing — Clothing to protect against heat and flame — Minimum performance requirements, ISO
- NFPA 2112 — TIA 23-1 (2023 edition): flame resistance and no melt/drip requirements, NFPA

