Short answer: what you must have before sending greige fabric
Sending greige fabric to a dyeing mill goes well when the fabric arrives with four things: a written spec that matches every roll, a clear colour target, test methods named by standard, and clean, labelled rolls. The mill inspects the greige before any chemical step, dyes to the approved lab dip, and returns the finished roll with a quality report.
What is greige (grey) fabric
Greige (grey) fabric is woven cloth that has not been bleached, dyed or finished yet — its beige-grey colour comes from the natural yarn and the sizing applied during weaving. Commission dyeing is the model where a trader buys greige from a weaving mill and sends it to a dyeing mill for bleaching, dyeing and finishing to order.
Step 1 — what does the spec sheet need?
The spec is the document every later step refers to, and it must match the physical rolls:
- Construction — fibre (e.g. TC, TR, cotton), yarn counts for warp and weft, density (ends × picks), weave structure (plain, twill)
- Size — usable width, weight (gsm), length per roll
- The job — colour, functions/finishes, test methods
The common mistake is a spec that does not match the fabric (e.g. actual width below the stated width), which causes disputes at intake — measure the width at several points along every roll before it ships.
Step 2 — how do you inspect the greige before shipping?
Use one of the defect-grading systems standard in the trade:
- 4-point system (ASTM D5430) — points follow defect length: up to 7.5 cm = 1 point, over 7.5 to 15 cm = 2 points, over 15 to 23 cm = 3 points, over 23 cm = 4 points; no more than 4 points per linear yard or metre of fabric, expressed as points per 100 square yards
- 10-point system — the other widely used grading system in the trade (Cotton Incorporated lists the 4-point and 10-point systems as the two most common worldwide)
Flag every defect on the selvedge and keep the inspection report. This matters because the dyeing mill's intake inspection is its first QC checkpoint: Boonchuay Industrial inspects and marks greige faults before any chemical is applied, and faults that arrive with the fabric will appear in the lot's quality report.
Step 3 — how do you set the colour target: spec, sample or swatch card?
A dyeing job starts three ways:
- A colour spec — a named or coded colour from a standard colour system
- A colour sample to match — send a physical sample (e.g. from a garment or a previous lot) and the mill matches it
- A standard swatch card — pick from the mill's ready standard colours
The mill's colour lab then produces a lab dip — a small sample colour-matched with a spectrophotometer and checked in a light booth. The buyer approves the lab dip before bulk runs: every roll of the bulk is dyed against the approved lab dip.
Step 4 — what functions and test methods do you specify?
- Functions/finishes — state what the fabric must do: water repellent, water and oil repellent, soil release, easy care, quick dry, flame retardant, anti-bacterial, deodorant, anti-mosquito — a full-service dyeing mill such as Boonchuay Industrial runs all nine groups
- Test methods — specify standard + grade + condition, e.g. "washing fastness grade 4 per ISO 105-C06" or "rubbing fastness grade 4 per ISO 105-X12" — different methods give different results, so a spec that names the standard is comparable across lots
- Volume — state it clearly, because the mill chooses the dyeing route to fit it: batch (jet) for small runs, continuous for large runs (light to dark shades), cold pad batch in between
- MOQ — say "negotiable" in your enquiry, and do not write a lead time into the spec before the mill confirms one
Step 5 — how do you label and ship the fabric?
- Greige rolls normally travel unwrapped — keep them clean and dry in a covered vehicle and off wet floors
- Label every roll or bale — construction, colour code, length, width, roll number
- Keep constructions and grades separate — never mix different constructions in one lot
- Documents that travel with the fabric — the spec sheet, the roll length list, the greige inspection report, the approved lab dip
Step 6 — how do you check the bulk before the fabric comes back?
- The mill dyes the bulk against the lab dip with in-process checks
- The buyer checks a sample from the bulk before the lot is released
- Final inspection at packing — Boonchuay Industrial runs three checkpoints: greige intake, in-process, and at packaging
- You receive a quality report — Boonchuay Industrial issues a 10-point-system quality report with every lot, plus in-house lab test results to ISO, AATCC, JIS and Daimaru methods
Boonchuay Industrial: a dyeing mill with over 60 years
Boonchuay Industrial (BCI) is a commission dyeing and finishing mill in Sam Phran, Nakhon Pathom, with over 60 years of experience, set up to take greige fabric in and finished rolls out:
- Colour lab — spectrophotometer, multi-source light booth, automatic dye dispensing, and lab dyeing that duplicates the factory's real production process (batch and continuous)
- Three QC checkpoints — greige intake (faults marked), in-process, and at packaging
- 10-point-system quality report on every lot, plus in-house lab testing to ISO, AATCC, JIS and Daimaru
- All three dyeing routes — batch (jet), continuous (light to dark), cold pad batch
- MOQ is negotiable — depends on process, colour and volume
- ISO 9001, ISO 14001 and OEKO-TEX® STANDARD 100 certified
See commission dyeing from a dyeing mill · one-stop service from greige to finished fabric · or contact the BCI team
FAQ
Q: Does ordering many colours cost more? A: No — cost follows the batch size per colour, not the number of colours. Boonchuay Industrial dyes by batch and continuous routes to fit each volume, and keeps colour consistent across colours and lots with its colour lab and lab dip.
Q: Will a dyeing mill accept greige fabric that has faults? A: Yes, but it inspects on intake — Boonchuay Industrial checks and marks greige faults before any chemical is applied, and those faults appear in the lot's quality report.
Q: How is a lab dip approved? A: The colour lab matches the target with a spectrophotometer, the sample is checked in a light booth, and the buyer approves the lab dip before bulk runs — it becomes the colour standard for every roll.
Q: Which test methods should I specify? A: Name the standard for each requirement: washing fastness ISO 105-C06 / AATCC 61, rubbing ISO 105-X12, light fastness ISO 105-B02, dimensional change ISO 6330 — the BCI lab tests to ISO, AATCC, JIS and Daimaru methods.
Q: Can I send small volumes? A: Yes — MOQ is negotiable, depending on process, colour and volume.
References
- Standard Test Methods for Visually Inspecting and Grading Fabrics (ASTM D5430, 4-point system) — ASTM International
- Fabric Defects Classification (4-point and 10-point systems) — Cotton Incorporated
- ISO 105-C06:2010 Textiles — Tests for colour fastness — Part C06: Colour fastness to domestic and industrial wet cleaning — ISO
- Test Methods and Standards — AATCC

